You may want to specify executable and core dump file names. The usual way to do this is at start-up time, using the arguments to GDB's start-up commands (see section Getting In and Out of GDB).
Occasionally it is necessary to change to a different file during a GDB session. Or you may run GDB and forget to specify a file you want to use. In these situations the GDB commands to specify new files are useful.
runcommand. If you do not specify a directory and the file is not found in the GDB working directory, GDB uses the environment variable
PATHas a list of directories to search, just as the shell does when looking for a program to run. You can change the value of this variable, for both GDB and your program, using the
pathcommand. On systems with memory-mapped files, an auxiliary file `filename.syms' may hold symbol table information for filename. If so, GDB maps in the symbol table from `filename.syms', starting up more quickly. See the descriptions of the file options `-mapped' and `-readnow' (available on the command line, and with the commands
add-symbol-file, described below), for more information.
filewith no argument makes GDB discard any information it has on both executable file and the symbol table.
exec-file [ filename ]
PATHif necessary to locate your program. Omitting filename means to discard information on the executable file.
symbol-file [ filename ]
PATHis searched when necessary. Use the
filecommand to get both symbol table and program to run from the same file.
symbol-filewith no argument clears out GDB information on your program's symbol table. The
symbol-filecommand causes GDB to forget the contents of its convenience variables, the value history, and all breakpoints and auto-display expressions. This is because they may contain pointers to the internal data recording symbols and data types, which are part of the old symbol table data being discarded inside GDB.
symbol-filedoes not repeat if you press RET again after executing it once. When GDB is configured for a particular environment, it understands debugging information in whatever format is the standard generated for that environment; you may use either a GNU compiler, or other compilers that adhere to the local conventions. Best results are usually obtained from GNU compilers; for example, using
gccyou can generate debugging information for optimized code. On some kinds of object files, the
symbol-filecommand does not normally read the symbol table in full right away. Instead, it scans the symbol table quickly to find which source files and which symbols are present. The details are read later, one source file at a time, as they are needed. The purpose of this two-stage reading strategy is to make GDB start up faster. For the most part, it is invisible except for occasional pauses while the symbol table details for a particular source file are being read. (The
set verbosecommand can turn these pauses into messages if desired. See section Optional warnings and messages.) We have not implemented the two-stage strategy for COFF yet. When the symbol table is stored in COFF format,
symbol-filereads the symbol table data in full right away.
symbol-file filename [ -readnow ] [ -mapped ]
file filename [ -readnow ] [ -mapped ]
mmapsystem call, you can use another option, `-mapped', to cause GDB to write the symbols for your program into a reusable file. Future GDB debugging sessions map in symbol information from this auxiliary symbol file (if the program has not changed), rather than spending time reading the symbol table from the executable program. Using the `-mapped' option has the same effect as starting GDB with the `-mapped' command-line option. You can use both options together, to make sure the auxiliary symbol file has all the symbol information for your program. The auxiliary symbol file for a program called myprog is called `myprog.syms'. Once this file exists (so long as it is newer than the corresponding executable), GDB always attempts to use it when you debug myprog; no special options or commands are needed. The `.syms' file is specific to the host machine where you run GDB. It holds an exact image of the internal GDB symbol table. It cannot be shared across multiple host platforms.
core-file [ filename ]
core-filewith no argument specifies that no core file is to be used. Note that the core file is ignored when your program is actually running under GDB. So, if you have been running your program and you wish to debug a core file instead, you must kill the subprocess in which the program is running. To do this, use the
killcommand (see section Killing the child process).
loadcommand may be available. Where it exists, it is meant to make filename (an executable) available for debugging on the remote system--by downloading, or dynamic linking, for example.
loadalso records the filename symbol table in GDB, like the
add-symbol-filecommand. If your GDB does not have a
loadcommand, attempting to execute it gets the error message "
You can't do that when your target is ..." The file is loaded at whatever address is specified in the executable. For some object file formats, you can specify the load address when you link the program; for other formats, like a.out, the object file format specifies a fixed address. On VxWorks,
loadlinks filename dynamically on the current target system as well as adding its symbols in GDB. With the Nindy interface to an Intel 960 board,
loaddownloads filename to the 960 as well as adding its symbols in GDB. When you select remote debugging to a Hitachi SH, H8/300, or H8/500 board (see section GDB and Hitachi microprocessors), the
loadcommand downloads your program to the Hitachi board and also opens it as the current executable target for GDB on your host (like the
loaddoes not repeat if you press RET again after using it.
add-symbol-file filename address
add-symbol-file filename address [ -readnow ] [ -mapped ]
add-symbol-filecommand reads additional symbol table information from the file filename. You would use this command when filename has been dynamically loaded (by some other means) into the program that is running. address should be the memory address at which the file has been loaded; GDB cannot figure this out for itself. You can specify address as an expression. The symbol table of the file filename is added to the symbol table originally read with the
symbol-filecommand. You can use the
add-symbol-filecommand any number of times; the new symbol data thus read keeps adding to the old. To discard all old symbol data instead, use the
add-symbol-filedoes not repeat if you press RET after using it. You can use the `-mapped' and `-readnow' options just as with the
symbol-filecommand, to change how GDB manages the symbol table information for filename.
add-shared-symbol-filecommand can be used only under Harris' CXUX operating system for the Motorola 88k. GDB automatically looks for shared libraries, however if GDB does not find yours, you can run
add-shared-symbol-file. It takes no arguments.
sectioncommand changes the base address of section SECTION of the exec file to ADDR. This can be used if the exec file does not contain section addresses, (such as in the a.out format), or when the addresses specified in the file itself are wrong. Each section must be changed separately. The "info files" command lists all the sections and their addresses.
info targetare synonymous; both print the current target (see section Specifying a Debugging Target), including the names of the executable and core dump files currently in use by GDB, and the files from which symbols were loaded. The command
help targetlists all possible targets rather than current ones.
All file-specifying commands allow both absolute and relative file names as arguments. GDB always converts the file name to an absolute file name and remembers it that way.
GDB supports SunOS, SVr4, Irix 5, and IBM RS/6000 shared libraries.
GDB automatically loads symbol definitions from shared libraries
when you use the
run command, or when you examine a core file.
(Before you issue the
run command, GDB does not understand
references to a function in a shared library, however--unless you are
debugging a core file).
run. If regex is omitted all shared libraries required by your program are loaded.
Go to the first, previous, next, last section, table of contents.